Order for this Paper or Similar Assignment Writing Help

Fill a form in 3 easy steps - less than 5 mins.

Posted: February 9th, 2023

Tensile Test Laboratory Report

Tensile Test Laboratory Report
In mechanical testing, one of the common properties widely used is the strength of materials. In this lab report, tensile testing was used to determine these strengths. The experiment provides details on the mechanical behavior or strength of a material. The foundational idea is to place the material specimen between fixtures known as grips which clamp the specimens. For comparison purposes, these materials should have equal dimensions of initial measurements such as lengths, and cross-sectional areas (Callister & Rethwisch, 2007). After confirming these dimensions, we can then begin to apply the loads or forces or weights while at the same time recording the change in lengths as the weights are steadily increased.
A very simple test requires one to hang some materials on an immovable grip and the weights on hooked end. To ensure the change in the consecutive lengths, add the weights to keep the material to stretch until the point of breakage. The experiment gives a result of a graph of force (N) against extension (mm), and because the force required in stretching the materials depends on the strength of the materials, a comparison between the specimens can be easily obtained. The various abilities of the materials can be very crucial to a structural designer who must ensure that the materials withstand certain forces. This mechanical strengths and behavioral properties of materials can only be found when these materials are tested and pulled until breakage. In this experiment, the three materials which were brass, aluminum, steel and stainless steel were used as specimens. The strength properties were used to determine their tensile strengths and Young’s modulus.
The experiment is to examine the behavior of four material specimens under the tensile test. The materials under the test are brass, steel, aluminum and stainless steel. From the tensile test, the properties that will be determined are the tensile strengths, 0.2% proof stress and Young’s modulus (Yoshida, Uemori & Fujiwara, 2002). This experiment is used to establish materials properties. Moreover, it can be used in diverse industries. An example where the tensile test can be applied is to decide the Ultimate Tensile Stress required for building structures, railways, shopping bags, et cetera (Hosford & Caddell, 2011).
Equipment and Methodology
Four composite specimens of brass, stainless steel, steel, and aluminum, and which have equal dimensions. The test was performed by putting the specimens under a test machine that contain grips to hold the specimens (Meyers & Chawla, 2009). The machine then was allowed to exert tensile forces, causing the specimen to extend. As was read from the machine, the load per increment and the specimen extensions were written down for analysis. The loads and lengths of all the materials were recorded and then compared with each other.
Results and Analyses

Load (N)-Extension (mm) Curve for Brass, Stainless steel, steel, and Aluminum

Given the materials with equal dimensions, in this experiments case 10mm diameter and 60mm material length. We can perform the following calculations;
Tensile strength = (Maximum Load)/(Cross Sectional Area)
At the maximum load of 7665N, Stainless Steel Yields a tensile strength of
Tensile strength = 7665/78.57
= 97.55 N/mm2 Or 0.098kN/mm2
At the maximum load of 3769N, Brass Yields a tensile strength of
Tensile strength = 3769/78.57
= 47.97 N/mm2 Or 0.048kN/mm2
At the maximum load of 3652N, Steel Yields a tensile strength of
Tensile strength = 3652/78.57
= 46.48 N/mm2 Or 0.04648kN/mm2
At the maximum load of 811N, Aluminum Yields a tensile strength of
Tensile strength = 811/78.57
= 10.322 N/mm2 Or 0.0103kN/mm2
The Proof Stress at 0.2% of these materials can be calculated as follows;
0.2% of 60mm is equal to 12mm. Therefore, at 12 mm, by reading this value against the corresponding load, we get the proof load of Stainless steel as 0.06216kN, Brass as 0.034kN, and Steel as 0.03350kN. The aluminum breaks before attaining the 0.2% proof Load.
The 0.2% proof Stress is therefore given as;
Stainless Steel, Proof Load = 0.0621kN/78.57mm2
Proof Load= 0.00079kN/mm2
Brass, Proof Load = 0.034kN/78.57mm2
Proof Load= 0.000433kN/mm2
Steel, Proof Load = 0.0335kN/78.57mm2
Proof Load= 0.000424kN/mm2
Young’s Modulus
From an elastic curve region in the diagram, we can obtain Young’s Modulus (Chen, Gandhi, Lee, & Wagoner, 2016).
In stainless Steel experiment, Young^’ s Modulus = Stress/Strain
Stress= Load/(Cross Sectional Area)
Strain= Extension/(Original Length)
For Stainless Steel,
Stress= 3.384kN/78.57mm2
Strain= 0.3mm/60mm
Young^’ s Modulus = 0.04307/0.005
Young^’ s Modulus = 8.614kN/mm2
For Brass,
Stress= 2.168kN/78.57mm2
Strain= 0.3mm/60mm
Young^’ s Modulus = 5.519kN/mm2
For Steel,
Stress= 1.318kN/78.57mm2
Strain= 0.17mm/60mm
Young^’ s Modulus = 0.01677/0.002833
Young^’ s Modulus = 5.92kN/mm2

For Aluminum,
Stress= 0.569kN/78.57mm2
Strain= 0.17mm/60mm
Young^’ s Modulus = 0.00724/0.002833
Young^’ s Modulus = 2.56kN/mm2
These graphical analyses were conducted from the data that was obtained from the specimens after the experimentations. From the load-extension curves, the tensile strengths, 0.2% proof stress and Young’s modulus for the four specimens are as calculated below.
The first phase of each graph is the elastic region. This is where the specimens extend uniformly with the load added. The second stage when the curve begins to bend is known as the offset yield strength; in this lab, calculated at 0.2%. After the materials extend up to the maximum reachable stress, they fail to hold any more loads and; therefore, break. This point of breakage is known as the Fracture point. The elasticity limits of brass, stainless steel, steel, and aluminum differ with their respective tensile strengths obtained from the calculations. From our analysis, stainless steel is found to have the highest tensile strength, followed by the brass, steel and finally the aluminum is the weakest (Ross, Irvin, & Roth, 2007). This means that in structural engineering, stainless steel can be the most preferred where stronger tensile forces are needed.
The tensile tests on stainless steel, brass, steel, and aluminum identify stainless steel to be having the highest tensile strength followed by brass, steel and finally aluminum in the above order. These results also mean that the structures made from these materials have the ability to carry heavy loads in that order starting from the stainless steel, the strongest material. By knowing the strengths of particular materials, an engineer is able to identify their suitability in coming up with rails, buildings, shopping bags and other structures. To avoid fractures and breakages, the carrying capacity of these materials must not be surpassed (Callister & Rethwisch, 2007).
Callister, W. D., & Rethwisch, D. G. (2007). Materials science and engineering: an introduction (Vol. 7, pp. 665-715). New York: Wiley.
Chen, Z., Gandhi, U., Lee, J., & Wagoner, R. H. (2016). Variation and consistency of Young’s modulus in steel. Journal of Materials Processing Technology, 227, 227-243.
Hosford, W. F., & Caddell, R. M. (2011). Metal forming: mechanics and metallurgy. Cambridge University Press.
Meyers, M. A., & Chawla, K. K. (2009). Mechanical behavior of materials (Vol. 2, pp. 420-425). Cambridge: Cambridge university press.
Ross, C. D., Irvin, D. B., & Roth, J. T. (2007). Manufacturing aspects relating to the effects of direct current on the tensile properties of metals. Journal of engineering materials and technology, 129(2), 342-347.
Yoshida, F., Uemori, T., & Fujiwara, K. (2002). Elastic–plastic behavior of steel sheets under in-plane cyclic tension–compression at large strain. International Journal of Plasticity, 18(5), 633-659.

Tags: , , , ,

Homework Help For You!

Special Offer! Get 20-30% Off on Every Order!

Why choose us?

Every student wants the best grades and that’s our Focus

Top Essay Writers

We carefully choose the most exceptional writers to become part of our team, each with specialized knowledge in particular subject areas and a background in academic research writing.

Affordable Prices

Our service prioritizes recruiting the most talented writers at an affordable cost. We facilitate the lowest possible pricing without compromising the quality of our services. Our costs are student friendly and competitive in comparison to other writing services in the industry.

100% Plagiarism-Free

The service guarantees that our final work is 100% original and plagiarism-free, ensuring this through a thorough scan of every draft copy using advanced plagiarism detection software before releasing it to be delivered to our valued customers.

How it works

When you decide to place an order with Nursing Assignment Answers, here is what happens:

Complete the Order Form

You will complete our order form, filling in all of the fields and giving us as much detail as possible.

Assignment of Writer

We analyze your order and match it with a writer who has the unique qualifications to complete it, and he begins from scratch.

Order in Production and Delivered

You and,the support and your writer communicate directly during the process, and, once you receive the final draft, you either approve it or ask for revisions.

Giving us Feedback (and other options)

We want to know how your experience went. You can read other clients’ testimonials too. And among many options, you can choose a favorite writer.